Buy Forrest CM10806105 Chopmaster 10-Inch 80 Tooth ATBR Miter and Radial Saw Blade with 5/8-Inch ArborForrest CM10806105 Chopmaster 10-Inch 80 Tooth ATBR Miter and Radial Saw Blade with 5/8-Inch Arbor Product Description:
- 20° Face Hook for easy feed
- DOUBLE HARD and 40% STRONGER C-4 CARBIDE will give up to 300% longer life between sharpenings.
- Ends second-step finishing (jointing and sanding not required).
- Buy and sharpen ONE blade instead of 3, (24T Rip, 50T Combination, 80T Crosscut).
- Ends cutting 1/16" oversize to allow for RESURFACING
Product Description
Maintain maximum stability for the best cut with a Forrest Chopmaster Saw Blade. Specially designed for sliding compound miter and radial-arm saws, grabbing and throwing of scrap cutoffs has been minimized with this design.This blade has a heavier than normal steel plate and a negative face hook. Its made with double-hard C-4 submicron carbide for up to 300 longer life. Each blade is hand-straightened to a runout of .001"/.002" for maximum cut quality The tooth style (4 points and flat) produces steady, clean cuts with no bottom splintering. Youll be delighted by the extra smooth, tight cuts youll get with this blade. The 10" blade has a 7/64" kerf and 5/8" arbor hole.
Customer Reviews
Most helpful customer reviews
52 of 53 people found the following review helpful.
The Best Blade - Bar None
By Richard
A little "pricey" but well worth it! No other saw blade on the market can compete with Forrest. It blows Freud away. Quiet, no vibration, flat & true and your cuts look like they were sanded with 200 grit sandpaper. And that's just the product. Before buying this blade I had questions about the kerf width so I called Forrest. It was after hours I didn't expect an answer, but Mr. Forrest himself answered the phone. I was blown away that he answers his own phone; try to get the president of Freud on the phone. He and I spoke for a good 15-20 minutes. Mr. Forrest personally told me if for any reason I didn't like HIS blade he would buy it back from me no questions asked. He also told me in all his years in business he has never had to buy back a blade. It say's a lot when someone stands behind their product like that. Simply the best... Bar none!
42 of 44 people found the following review helpful.Freud vs. Forrest?
By Rich Guardia
I've owned the Freud LU85 & F80 crosscut blades. They in no way compare to the quality of the Chopmaster. The Forrest has no vibration at all! I mean none. The plate is so flat & true, when you pull the triger it feels like there isn't even a blade on the saw. It's also very quiet as well, no ringing after the blade comes to a stop. It cuts hardwood so smooth it's like it's been sanded to 600 grit paper. It cuts softwood very good to. I also considered the Ridge Carbide TS 1000 & Tenryu Miter Pro. They are all about the same price. I doubt you could go wrong with these two blades either. So spend the extra $... . Forget about Freud! They make good router bits, but their saw blades are just average compared to Forrest. It's like a Civic vs. a Ferrari....
9 of 9 people found the following review helpful.Outstanding Performance
By B. Keyes
Without a doubt, the very best blade I've used on my Makita Slide/Compound Miter Saw. I am a Contractor/Trim Carpenter and have used many different blades over the years. You simply can't go wrong with this product. Not the least expensive blade by any means, but unquestionably the best.
Latest Price: See on Amazon.com!
More Info: See on Amazon.com!
See Customers Review: See on Amazon.com!
