Buy Starrett C33H-6-4R 6-Inch Combination Square with Forged and Hardened Steel HeadStarrett C33H-6-4R 6-Inch Combination Square with Forged and Hardened Steel Head Product Description:
- Starrett 6-inch combination square with forged and hardened steel head, satin chrome blade, and smooth black enamel finish
- Get better accuracy and greater efficiency when making measurements
- Features easy-to-read, sharp 8ths, 16ths, 32nds, and 64ths graduations
- Square blades are machine divided, hardened and tempered for long life
- 1-by-0.7-by-6.6-inches and ships at 4.8-ounces; backed by Starrett 1-year limited warranty
- The square heads are forged hardened steel with smooth, black enamel finish.
- These squares have the same features as the No. 11 Series
Product Description
Starrett hardened steel squares are recommended when accuracy is required. Beams and chrome plated blades are hardened, ground and lapped to insure parallelism and straightness. Beam is grooved at inner corner for clearance of burr or dirt. Faces of the head are ground square. 3/32" x 3/4" x 6" blade with 3" long beam and 45 degree face - equipped with reversible lock bolt, spirit level and scribe. Forged and hardened head, smooth black enamel finish. Faces are 1/2" wide.
Customer Reviews
Most helpful customer reviews
7 of 7 people found the following review helpful.
Life is too short for a crudy square.
By J. Foote
If you use a square frequently, do treat yourself to a good one. Yup, they're expensive, but these folks earn their money doing wonderful metalwork. This is a quality of metalcasting, milling, etching and finish you just don't see very often. If you're like me, you'll find the resulting precision inspirational, useful, and a pleasure to use.Cheap squares are no fun at all, sticky, and like as not, not even square. In contrast, this 6" Starrett is simply substantial. I also use a 12" Mitutoyo set that's equally supurb. It's a one-time investment I enjoy every time I use it.
15 of 18 people found the following review helpful.Might as well get both now
By Bob Feeser
I just received the Starrett 6" and immediately ordered the 12. First I tried to rejuvenate an old one that belonged to my father. After a half hour of scrubbing, de-rusting, and fine polishing, I thought I had a twelve. I checked the depth accuracy, and it was right on. Then I checked it as a square. Although the end to end was correct, the center of the ruler had been accidentally ground. So if I tried to square up a 4" high table saw blade for example, it would be off. That was all I needed. I went to the computer and ordered the 12 as well. You can't afford to screw around with the device that all other tools are measured by. A cut only off 1 degree creates a 91-degree edge. When gluing and clamping that edge, it bows or skews your project. Then when you try to mate that up to a square project, it doesn't fit. Save yourself a lot of heartache, time, and money, get a starrett combination square.I have the Bosch digital protractor, and that measures in tenths of a degree. The problem is that it is about 18 inches long, and does not measure depths.These combination squares are great for taking a measurement in a difficult to get to area. You simply drop it into the area, slide the ruler out until it stops, then lock it into the base with the knob, then bring the square out, and check your measurement. No more having to dive your head under something, while you contort your body to be able to see the measurement.Pertaining to the 6 or 12, I chose the 6 first because I saw that one being used in higher end woodworking books. Authors even photographed themselves using the starret setting up the table saw blade for example. When I got it my first impression was, boy is that tiny. It probably will be the one that I use the most. I just don't want to be limited when I need to use one on lengths greater than 6 inches.It is well made, and yes it does spec out properly. I used Incra measuring instruments to check the rule, and the Bosch digital protractor to check to see if it was dead on 90. It wasn't off by even a tenth of a degree.It's funny how you have to rave about a tool that does what it is supposed to do, and do it well. Their is so much junk out there. Did you ever check your level, but putting it on a surface, then turn it around end to end to see if the bubble shows the same reading on the same surface. You will be shocked; 80 percent of them are off. Even the bubble on this Starrett tool is dead on.The square ness is right on. The typical check of taping a piece of paper to a flat surface in front of a fence, then use the square to draw a line, flip the tail of the square over to the other side, and see if the line is dead on.If you have a square that has a handle that was riveted, welded, or glued on, chances are it is off. The single stamped pieces of metal are usually accurate.These Starrett combination squares are something that you will grow to use more and more often. Soon you will wonder how you ever lived without it. Highly recommended.
9 of 10 people found the following review helpful.When It's Right To Be Square
By Marc Ruby™
I like making small boxes during the cold months when being in the shop is an invitation to pneumonia. Small boxes mean small tools, but a big increment in the requirements for precision. The tiny little bit off square that would never be noticable in a large table is a cardinal error in a 6" by 8" box.Starrett is the only answer if you want uncompromising accuracy. The straightedge is absolutely accurate. It body of the square holds it with no wobble at all. The bubble level really works, And everything, right down to the nifty scribing pin is machined perfectly. It's no lightweight, despite its size, and it will take a lot of banging and dropping without a flinch.All Starret tools are expensive, whether it's a 4" square or a 12" combinatiom square. Surprisingly, they are not the most expensive I've seen. But they aren't stamped out in mass quantities, they are individually inspected, and they come in their own little box. They aren't just the best, they are heirloom grade.I like the 6" square better than the 4", mostly because I'm slightly fumble fingered and there's more to hold. There's also a tiny symmetrical 3" that is great for showing off when you pull it out of your pocket.
Latest Price: See on Amazon.com!
More Info: See on Amazon.com!
See Customers Review: See on Amazon.com!
