TORMEK Planer/Jointer Blade Jig Product Description:
Product Description
For sharpening HSS steel blades of any length. Min. 1/2" width. Sweden
Customer Reviews
Most helpful customer reviews
32 of 32 people found the following review helpful.
It's a dream come true, we'll almost ~ Update
By Bob Feeser
***Update to my review seen below. I still love the Tormek system, but I have discovered a severe flaw. The bracket arms that hold the jigs on are not constructed at perfect 90 degree angles. This results in the jig and sharpener to be at off angles. This wouldn't matter if you were using the same bracket to use the truing tool as the one you are using to sharpen your planer blades, but that is not the case with the planer jig; it comes with its own bracket that is not a perfect 90, nor is it off by the same amount. So I had to place my bracket assembly in the vise, and after spending a good deal of time with a block of wood and a hammer try to straighten it out. I got the standard bracket that comes with the jig straightened out pretty well, but the one that comes with the planer/jointer blade jig would not straighten properly, it was that far out. So what you wind up with is a trued stone that is at an angle. In order to get the stone true to the planer jig surface, I have to put strong pressure on one side to actually bend the jig a little while tightening the screw, and that was after getting it as close as I could with the hammer in a vise.I didn't expect this kind of craftsmanship out of an $800 sharpening tool and jig set, which is what I paid. I don't want to overstate my case. I found the Tormek system to be true in every other way. The tops of the collars that receive the brackets are EXACTLY true along a horizontal plane to a perfect right angle to the stone. That is the side of the stone, what of course is most important here is the sharpening surface of the stone, and that is where the true brackets come into play.So if you are using the Tormek with the same bracket that comes with the machine, and not switching to another bracket like when installing the Planer/Jointer Blade jig, then you are ok. So what if the stone is off angle, the jig will run a parallel plane to it. But when going from one bracket to using the truing stone to surface the stone, and then switching to the planer/jointer attachment blade sharpener jig, you are dealing with a different bracket. You can check your jig by first taking out a square and seeing if the 2 bracket legs that go into the body of the Tormek are at a right angle to the wide part of the horizontal leg of the bracket. In plain words, check your bracket the jigs ride on and see if it was assembled squarely. The outer leg is part of the main rod just bent at 88 degrees for example, and should be 90 degree angle, and the inner rod is welded on and also at some angle that is not a 90 degree angle. If yours is at 90 then you got a good one, but after getting both the bracket that comes with the machine, and the bracket that comes with the planer/joiner attachment and they are both off, I doubt yours are true also.Since using the Tormek system with all of the jigs that come with it to perfectly sharpen your tools, since it is all done on the same bracket makes the off angle a mute point, I will leave the rest of my review below as it stands. This is just a comment of a problem of misalignment I found that becomes a problem when using the planer/jointer blade attachment since it has its own bracket it comes with.I was getting good results with it because I was changing the position of the blade and going ahead and sharpening my 12" planer blades just along the high spot of the stones face, but that seems like a lame thing to have to do. The rods/brackets should be made at a perfect 90 right from the factory.Now onto my original review and what an engineering marvel this thing is otherwise.By the way I am still sharpening my same jointer and planer blades again and again and at least on my Powermatic 8" jointer I am getting glass smooth wood surfaces. It's almost shiny.
16 of 16 people found the following review helpful.
Great Tool
By Gregory L. Goode
Every once in a while you find a really great deal. I'm an avid woodworker and bought a Tormek Super Grind a few months ago because I was tired of the drudgy of sharpening my chisels and lathe tools. I was amazed at he quality and speed of the Tormek system compared to the Delta sharpener it replaced. This is a woodworker's prayer come true. I immeadiately purchased the SVH-320 jointer and planer blade attachment. The system has already paid for itself in six months use. Quik and easy is an understatement. Blades, chisels, cutters and gouges are razor sharp and simple to touch up. The technical services and website are great. I can't recommend this equipment or company highly enough to do them justice.
15 of 16 people found the following review helpful.
Great way to sharpen your planer/jointer knives
By S. Boris
I recently spent $45 to have 2 sets of Dewalt planer blades sharpened by a sharpening service. They were out 2 weeks and shipping to and from the service did add up. I love to use barn boards for furniture projects but the problem is they are very hard on knives. I could not shift my jointer knives anymore because they were so knicked up. I bought this jig and it was very well designed. It will only sharpen a certain amount of each knife and it is repeatable. So you set it correctly on the first knife and then you can sharpen the other knives in the set the same way. The price may seem high to start with, but I figure once I sharpen my blades about 4 times (jointer/planer), I just paid for it. The Tormek system does take a little getting used to but now that I have the hang of it, I might be able to sharpen stuff for others and make a little extra $.
Latest Price: See on Amazon.com!
More Info: See on Amazon.com!
See Customers Review: See on Amazon.com!